安裝玻玻璃墻、門頂部限位槽的寬度應大于玻璃厚度2～4mm，槽深在20～30mm之間，以便注膠。濟南玻璃隔斷墻分享安裝方法可由所彈線引出兩條金屬裝飾板邊線，然后按邊線進行門框頂部限位槽的安裝。槽口內的木墊板是調整槽深的。通過墊板的增多或減少調整。

The width of the limit groove at the top of the glass wall and door shall be 2~4mm greater than the glass thickness, and the groove depth shall be 20~30mm for the convenience of glue injection. The shared installation method of Jinan glass partition wall can draw two metal decorative panel sidelines from the snapped line, and then install the limit slot at the top of the door frame according to the sidelines. The wooden backing plate in the groove is used to adjust the groove depth. Adjust by increasing or decreasing the base plate.

濟南玻璃安裝金屬飾面的木底托。安裝方法可在原預埋木磚上釘方木，或通過膨脹螺栓釘方木，把方木固定在地面上，然后再用***膠將金屬飾面板粘在木方上。鋁合金方管，可用鋁角固定在框柱上，或用木螺釘固定在埋入地面中的木磚上。

Jinan glass is installed with metal veneer wooden base. The installation method can be nailing the square timber on the original embedded wooden brick, or nailing the square timber with expansion bolts to fix the square timber on the ground, and then using all-purpose adhesive to stick the metal decorative panel on the wooden block. The aluminum alloy square tube can be fixed on the frame column with aluminum angle or on the wooden brick embedded in the ground with wood screws.

安裝堅向門框。按所彈線釘立門框方木，然后用膠合板確定門框柱的外形尺寸和位置的固定（注意應減除裝飾面尺寸）。后外包金屬裝飾面，包時要把飾面對頭接縫放置在安裝玻璃的兩側中間位置。接縫位置必須準確并保證垂直。

Install the rigid door frame. Nail the square timber of the door frame according to the snapped line, and then use plywood to determine the overall size and position of the door frame column (note that the size of the decorative surface should be deducted). The back shall be wrapped with metal decorative surface, and the facing butt joint shall be placed in the middle of both sides of the installation glass. The joint position must be accurate and vertical.

玻璃安裝。用玻璃吸盤器（或玻璃吸盤機）把厚玻璃吸緊吸住，然后手握吸盤把通過2～3人把厚玻璃板抬起并豎立起來移安裝地點準備就位。就位方法：應把玻璃上部插入門框頂部的限位槽內，然后把玻璃的下部放到底托上對正線，并對好兩側門框的安裝位置，使厚玻璃的兩側邊部正好封住門框的金屬飾面對縫口，要求做到內外都看不見飾面接縫口

Glass installation. Use a glass suction cup (or glass suction cup machine) to suck the thick glass tightly, and then hold the suction cup handle to lift and erect the thick glass plate through 2 to 3 people and move it to the installation site for preparation. Positioning method: insert the upper part of the glass into the limit slot on the top of the door frame, then put the lower part of the glass on the bottom bracket and align the installation position of the door frame on both sides, so that the two sides of the thick glass can just seal the metal facing butt joint of the door frame, and it is required to make the facing seam invisible both inside and outside

玻璃固定。在底托木上的內外釘兩根扁方木條把厚玻璃夾在中間，但距厚玻璃板需留出4mm左右的空隙，然后在扁方木條上涂刷***膠將飾面金屬板粘卡在方木和兩根扁方木條上。

Glass fixation. Nail two square battens on the inside and outside of the bottom joist to clamp the thick glass in the middle, but leave a gap of about 4mm from the thick glass plate, and then apply all-purpose adhesive on the square batten to stick the decorative metal plate on the square wood and two square battens.

注玻璃膠封口。在頂部根位槽兩側空隙內和底托玻璃槽口的兩側以及厚玻璃與門框柱的對縫處注入玻璃膠。注入順序應從某一條縫隙的端頭開始到末端終止，中途不得停頓。操作要領是：握緊嵌縫槍壓柄用力要均勻，同時順著縫隙移動的速度也要均勻，即隨著玻璃膠的擠出，勻速移動注膠口，使玻璃膠在縫隙處形成一條均勻的直線。后用塑料片刮去多余的玻璃膠并用干凈布擦去膠

Seal with glass glue. Inject glass glue into the gap on both sides of the top root slot, both sides of the bottom glass slot and the butt joint between the thick glass and the door frame column. The injection sequence shall start from the end of a gap to the end, and shall not stop halfway. The key points of operation are: hold the caulking gun pressure handle with even force, and move along the gap with even speed, that is, with the extrusion of the glass glue, move the glue injection port at a uniform speed, so that the glass glue forms a uniform straight line at the gap. After that, scrape off the excess glass glue with a plastic sheet and wipe off the glue with a clean cloth

玻璃之間對接。固定部分的厚玻璃板，由于寬度尺寸過大，必須用兩塊或兩塊以上進行拼裝而成，兩塊對齊拼接必然形成接縫，對接縫應留2～3mm的距離（對接縫的玻璃切口必須倒用）。玻璃固定后，要用玻璃膠入縫隙中，注滿后同樣要用塑料片把膠刮平，使縫隙形成一條潔凈的均勻直線，玻璃面上要用干凈布擦凈膠跡。

Butt joint between glass. The thick glass plate of the fixed part must be assembled with two or more pieces due to its large width. The two pieces must be aligned and spliced to form a joint. A distance of 2~3mm should be reserved for the joint (the glass cut of the joint must be reversed). After the glass is fixed, the glass glue shall be inserted into the gap, and the plastic sheet shall also be used to scrape the glue flat after filling, so that the gap forms a clean and uniform straight line, and the glue mark on the glass surface shall be wiped with a clean cloth.

以上就是濟南玻璃安裝廠家分享的陽臺玻璃窗安裝方法的知識問題講解，相信大家看了以后應該會有更多的認識了吧，內容僅供大家參考，有不懂的問題就來咨詢我們http://www.52yoga.net吧！

The above is the explanation of the knowledge of the installation method of balcony glass windows shared by Jinan glass installation manufacturers. I believe you will have more understanding after reading it. The content is for your reference only. If you don't understand the problem, please consult us http://www.52yoga.net Come on!